Qingdao Daeil Shanghai Huayuyi Marble Table + Interferometer DVIA-ML3000S (251229R1-1) Installation Report
Contents
Overview
Remote pre-tuning (预调试) of DVIA-ML3000S (S/N 251229R1-1) was performed at the pre-tuning site in Zhejiang, before the system is relocated to the final installation site in Shanghai.
Performance verification data was obtained via the UI program. Data is represented in Autospectrum and VC Curve format, and reference material on the vibration level is provided.
Vibration Isolation System Information
Model: DVIA-ML3000S (External Controller)
Serial Number: 251229R1-1
Engineer
Gyumin.park · DAEIL SYSTEMS
Tuning Date
2026.10.16
End User
Shanghai Huayuyi (上海华雨益)
Number of Tuning Trial
1st (Pre-tuning, Remote)
Site
Pre-tuning: Zhejiang, China / Final installation: Shanghai, China
Equipment
Manufacturer: -
Equipment: Marble Table + Interferometer (大理石+干涉仪)
Model: -
Vibration Specification
N/A (No vibration specification defined)
Acceptance criterion: No oscillation (抖动) of the system with Active ON.
Equipment Condition
Pre-tuning condition: interferometer not installed, marble load approx. 2,800 kg (almost the same as the final marble weight).
Tuning Request
Conclusion
Remote pre-tuning and vibration measurement of DVIA-ML3000S (S/N 251229R1-1) were completed.
No oscillation was observed with Active ON during the pre-tuning.
Floor vibration at the pre-tuning site was VC-C (Vertical), VC-E (Left to Right) and VC-E (Front to Back), and the isolator top reached VC-G level in all three axes.
Average attenuation (1–80 Hz): Vertical -27 dB / Left to Right -29 dB / Front to Back -19 dB.
The final performance may differ due to reassembly, the installation of the interferometer and side boxes, and the floor condition of the final site.
Measurement Summary
| Measurement Point | Vibration Specifications | Axis | Result | |
|---|---|---|---|---|
| Floor | DVIA-ML3000S | |||
| 1. Floor 2. DVIA-ML3000S | N/A | Vertical | VC-C | VC-G |
| Left to Right | VC-E | VC-G | ||
| Front to Back | VC-E | VC-G | ||
※ No vibration specification defined; results are shown as VC grade (1–80 Hz, 1/3 octave).
Measurement Data Obtained via UI Program
Vertical
Vertical — Autospectrum
Vertical — VC Curves
Left to Right
Left to Right — Autospectrum
Left to Right — VC Curves
Front to Back
Front to Back — Autospectrum
Front to Back — VC Curves
Installation Photo
Installation (Pre-tuning site, Zhejiang)
Nameplate (DVIA-ML3000S, S/N 251229R1-1)
Reference
The table below classifies vibration levels based on IEST-RP-CC012.2.
Notes:
- As measured in one-third octave bands of frequency over the frequency 8 to 80 Hz (VC-A and VC-B) or 1 to 80 Hz (VC-C through VC-G).
- The detail size refers to the width in the case of microelectronics fabrication, the particle (cell) size in the case of medical and pharmaceutical research, etc. It is not relevant to imaging associated with probe technologies, AFMs, and nanotechnology.
The information given in this table is for guidance only. In most instances, it is recommended that the advice of someone knowledgeable about applications and vibration requirements of the equipment and processes be sought.
Share this Case Study
Case Study Information
Related Case Studies

Biel Crystal Manufactory Limited Raith EBPG5200 Plus E-Beam Lithography DVIA-ML3000S (260406R2-1) Installation Report

CEPREI Thermo Fisher Scientific (S)TEM Talos F200X DVIA-ML3000 (260424R5) Installation Report
