YIMO TECH ZEISS EVO 18 SEM DVIA-UB700 Installation Report
Contents
Overview
The DVIA-UB700 installed in Shanghai in 2019 (1st tuning: 2019.11.07) was re-tuned, and vibration measurement was performed.
Vibration measurement was conducted with the equipment in the Idle state.
Data is represented in Autospectrum format and reference material on the vibration level is provided.
Vibration Isolation System Information
Model: DVIA-UB700
Serial Number: 190903R1
Engineer
Younguk KIM · DAEIL SYSTEMS
Tuning Date
2026.11.09
End User
Shanghai Maritime Safety Administration, Nenjiang Road Base
Number of Tuning Trial
2nd
Location
Shanghai, China
Equipment
Manufacturer: ZEISS
Equipment: SEM
Model: EVO 18
Vibration Specification
Applied specification: ZEISS EVO series floor vibration specification (manufacturer) — less than 6 µm/s RMS up to 30 Hz and less than 12 µm/s RMS above 30 Hz, in three orthogonal axes.
| Direction | Frequency [Hz] | Allowable [µm/s RMS] |
|---|---|---|
| Horizontal (X, Y) | 1 – 30 | 6 |
| 30 – 80 | 12 | |
| Vertical (Z) | 1 – 30 | 6 |
| 30 – 80 | 12 |
Equipment Condition
Idle
Engineering Tool & Setup
| Item | UI (built-in sensors) |
|---|---|
| Instrument · Software | DVIA-UB700 controller · DAEIL SYSTEMS Tuning Software (UI) |
| Sensor | Built-in velocity sensors (Top / Bottom) |
| Measurement Point | Top = DVIA-UB700 isolated platform / Bottom = floor side (base) — measured simultaneously |
| Axis | Vertical / Left to Right / Front to Back — one axis at a time |
Conclusion
Following the 2nd tuning of the DVIA-UB700 active vibration isolation system, the vibration on the isolated platform satisfies the ZEISS EVO series floor vibration specification in all three axes.
Measurement Summary
| Axis | Result | Status | ||
|---|---|---|---|---|
| Floor | DVIA-UB700 | Floor | DVIA-UB700 | |
| Vertical | 1.7 µm/s @ 3.0 Hz | 0.70 µm/s @ 3.0 Hz | ✓ PASS | ✓ PASS |
| Left to Right | 1.3 µm/s @ 4.7 Hz | 0.84 µm/s @ 2.4 Hz | ✓ PASS | ✓ PASS |
| Front to Back | 2.6 µm/s @ 3.2 Hz | 1.0 µm/s @ 2.9 Hz | ✓ PASS | ✓ PASS |
Results are the peak values of the velocity Autospectrum (µm/s RMS). The floor and the isolated platform are each compared with the allowable level in Section 9.
Measurement Data
Vertical
Vertical – Autospectrum (SPEC: ZEISS EVO series)
Left to Right
Left to Right – Autospectrum (SPEC: ZEISS EVO series)
Front to Back
Front to Back – Autospectrum (SPEC: ZEISS EVO series)
Installation Photo
ZEISS EVO 18 on the DVIA-UB700
Reference
The table below classifies vibration levels based on IEST-RP-CC012.2.
¹ As measured in one-third octave bands of frequency over the frequency range 8 to 80 Hz (VC-A and VC-B) or 1 to 80 Hz (VC-C through VC-G).
² The detail size refers to line width in the case of microelectronics fabrication, the particle (cell) size in the case of medical and pharmaceutical research, etc. It is not relevant to imaging associated with probe technologies, AFMs, and nanotechnology.
The information given in this table is for guidance only. In most instances, it is recommended that the advice of someone knowledgeable about applications and vibration requirements of the equipment and processes be sought.
Share this Case Study
Case Study Information
Related Case Studies

Ulsan Technopark ZEISS SEM EVO10 DVIA-UB700 (220811R2) Installation Report

Hanyang University ZEISS Sigma 300 DVIA-UB700 Installation Report
